To e-mail Dr.Salmon click on the address above.
Troubleshooting
Dr. Salmon has a library of books and conference proceedings unrivalled in the industry and a collection of more than 3,000 reference papers and articles. The books and proceedings are available for loan, at a nominal fee to cover shipping, processing and handling and, in some cases, there will be a refundable deposit required where the article is especially rare. Scroll down the page to see front covers, titles, authors and year published. Click on the covers for PDF contents pages where available and click "back" in your browser to return.
Library of Technical Reference Books
THE GRINDING WHEEL - A Textbook of Modern Grinding Practice by Kenneth B. Lewis. The revised edition by W.F Schleicher was published under the auspices of the Grinding Wheel Institute, Cleveland, Ohio, USA, in 1958. (527 pages.)
PRECISION GRINDING TECHNIQUES - An Introduction to Precision Toolroom Grinding. Published by Jones & Shipman plc., Leicester, England. The first edition was published in 1952. This is the 3rd revised edition published in 1984. (95 pages.)
GRINDING TECHNOLOGY by Stephen F. Krar and J. William Oswald. Published by Delmar Publishers Inc., Albany New York, USA in 1974. (269 pages.)
ABRASIVE METHODS ENGINEERING - Volumes I and II by Francis T. Farago. Published by the Industrial Press in 1980 and first printed in 1976. (Volume I, 366 pages and Volume II 508 pages.)
MACHINING WITH ABRASIVES by Richard L. McKee. Published by Van Nostrand Reinhold in 1982. (304 pages.)
ABRASIVE MACHINING HANDBOOK by Stuart C. Salmon. Published by Hauni-Blohm and Hanui-Schaudt, the Grinding Division of Hauni-Werke Korber & Co. KG., Hamburg, Germany, in 1984. (177 pages.)
CREEP FEED GRINDING by Colin Andrew, Trevor Howes and Tom Pearce. Published by the Industrial Press in 1985. (272 pages.)
HANDBOOK OF MODERN GRINDING TECHNOLOGY by Robert King and Robert Hahn. Published by Chapman and Hall in 1986. (360 pages.)
SUPERABRASIVE GRINDING by J.L. Metzger. Published by Butterworths in 1986. (226 pages.)
GRINDING TECHNOLOGY by Stephen Malkin. Published by the Society of Manufacturing Engineers, Dearborn, MI, USA, in 1989. (275 pages.)
SUPERABRASIVES - GRINDING AND MACHINING by Stephen Krar and Ernest Ratterman. Published by Glencoe/McGraw-Hill in 1990. (196 pages.)
CUTTING AND GRINDING FLUIDS - SELECTION AND APPLICATION (Second Edition) by Jeffrey D. Silliman. Published by the Society of Manufacturing Engineers, Dearborn, MI, USA, in 1992. (216 pages.)
CUTTING AND GRINDING FLUIDS - SELECTION AND APPLICATION by R.K. Springborn. Published by the American Society of Tool and Manufacturing Engineers, Dearborn, MI, USA, in 1967. (172 pages.)
ABRASIVES by L. Coes. Published by Springer-Verlag in 1971. (177 pages.)
MODERN GRINDING PROCESS TECHNOLOGY by Stuart C. Salmon. Published McGraw-Hill, New York, NY, USA, in 1992. (225 pages.)
PRINCIPLES OF ABRASIVE PROCESSING by Milton C. Shaw. Published by Clarendon, Oxford University Press, England, in 1996. (574 pages.)
MECHANICAL DEBURRING AND SURFACE FINISHING TECHNOLOGY by Alfred F. Scheider. Published by Marcel Dekker in 1990. (152 pages.)
METALWORKING FLUIDS by Jerry P. Byers. Published by Marcel Dekker, in 1994. (487 pages.)
METALWORKING FLUIDS (Second Edition) by Jerry P. Byers. Published by the Society of Tribologists and Lubrication Engineers - Taylor & Francis, in 2006. (463 pages.)
TECHNOLOGIE DES HOCHLEISTUNGSFLACHSCHLEIFENS (HIGH-SPEED SURFACE GRINDING TECHNOLOGY) (a dissertation, in German) by T. Tawakoli. Published by the University of Bremen, in 1989. (165 pages.)
HIGH EFFICIENCY DEEP GRINDING (HEDG) (in German) by P.Gunther Werner. Published Deutsches Industrieforum fur Technologie, in 1995. (39 pages.)
CREEP-FEED SURFACE GRINDING (a dissertation) by Stuart C. Salmon. Published the University of Bristol, Department of Mechanical Engineering, in 1979. (171 pages.)
The following books are collections of writings, papers and articles from various authors, compiled into one volume.
GRINDING STRESSES - CAUSE, EFFECT AND CONTROL. Published by the Grinding Wheel Institute, Cleveland, OH, USA. (circa late 1960's, early 1970's. 80 pages.)
A MANUAL OF PROCESSES FOR ABRASIVE CUT-MACHINING OF METALS by Edward De Witt, published by Wallace Supplies Manufacturing Company, Chicago, IL, USA. (A selection of writings from the mid 1950's to the early 1970's.)
GRITS AND GRINDS 1969 Published by the Norton Company, Worcester, MA, USA.
ULTRAHARD MATERIALS APPLICATION TECHNOLOGY Edited by Paul Daniel, published by De Beers Industrial Diamond Division, Ascot, England, in 1984. (115 pages)
GRINDING - THEORY, TECHNIQUES AND TROUBLESHOOTING Edited by Chander Bhateja and Richard Lindsay, published by the Society of Manufacturing Engineers, Dearborn, MI, USA, in 1982. (272 pages)
COST GUIDE FOR AUTOMATIC FINISHING PROCESSES. Edited by Lawrence J. Rhodes, published by the Society of Manufacturing Engineers, Dearborn, MI, USA, in 1981. (209 pages)
The following books are reference books and text books related to grinding, manufacturing processes, production engineering and management.
ANSI STANDARDS B11.9.1975 and B7.1-1978. Safety Requirements for the Construction, Use, Care and Protection of Abrasive Wheels and Grinding Machines. Published by ANSI, New York, NY, USA.
CURRENT GLOBAL RESEARCH PROJECTS IN FIXED ABRASIVE GRINDING by John A. Webster. Published in 2005 by AMT, the Association for Manufacturing Technology. (508 pages.)
MANUFACTURING ENGINEERING EXPLORES GRINDING TECHNOLOGY Edited by Tom Drozda, published by the Society of Manufacturing Engineers, Dearborn, MI, USA, in 1982. (193 pages)